Acrosser AR-B5630 Manual de usuario Pagina 1

AR-B5630 Socket P Intel® Core™2 Duo EPIC SBC with Intel® GME965 Express Chipset , DVI/LCD, Dual LAN and PCI-104 Eexpansion User Guide

102. INSTALLATION This chapter describes how to install the AR-B5630. At first, the layout of AR-B5630 is shown, and the unpacking information that y

11 3. CONNECTION The connectors on AR-B5630 allows you to connect external devices such as USB devices, serial port drives, hard disk devices, etc. T

12 1.DDR2ONNECTOR2.CF CONNECTOR

133.1 AT POWER INPUT (PWR2) 3.2 ATX FUNCTION CONNECTOR (CON2) 3.3 SATA POWER (CON3) 3.4 SERIRQ CONNECTOR (JP2)

143.5 CPU FAN (FAN1) 3.6 PCI104 (J10) 3.7 SATA CONNECTOR (SATA1) PIN SIGNAL PIN SIGNAL1 GND 2 Tx+ 3 Tx- 4 GND 5 Rx+ 6 Rx-

153.8 PATA CONNECTOR (IDE1) Pin Signal Pin Signal 1 -RESET 2 GROUND 3 DATA 7 4 DATA 8 5 DATA 6 6 DATA 9 7 DATA 5 8 DATA 10 9 DATA 4

163.11 BATTERY CONNECTOR (BAT1) 3.12 COMS CLAER CONNECTOR(J5) 3.13 EYBOARD/MOUSE CONNECTOR (KM1) 1 KDT3 GND2 MDT6 MCLK 4 VCC1 2 3 4

17 3.16 RJ45 CONNECTOR (LAN2) 18 3.17 RJ45 CONNECTOR (LAN1) 18 3.18 DB-15 VGA CONNECTOR (VGA1) PIN (LAN1

18 3.19 DVI-I CONNECTOR (DVI1) 3.20 TV-OUT (TVCON1) PIN SIGNAL PIN SIGNAL1 RED 9+5V 2 GREEN 10 GND

193.21 COM2 (COM1) 3.22 COM1 (CON1) 3.23 COM3 (COM2) PIN SIGNAL PIN SIGNAL1 /DCDB 2 /DSRB3 RXDB 4 /RTS

2 Table of Contents 0. PREFACE...

203.24 COM4 (COM3) 3.25 SYSTEM FAN (FAN2) 3.26 AUDIO CONNECTOR (AUDIO1) PIN SIGNAL PIN SIGNAL1 LINE OUT

21 3.27 PANEL POWER SELECTOR (J1) 3.28 GPIO (GPIO1) PIN SIGNAL PIN SIGNAL1 GPIO0 2 VCC 3 GPIO1 4 GPIO75 GPIO2 6 GPIO67 GPIO3 8 GPIO59

22 3.30 RS422/RS485 CONNECTOR (J9) 3.31 IR CONNECTOR (IR1) 3.32 PANEL POWER SELECTOR (J1) 3.33 LVDS POWER (LCDPW

233.34 LVDS CONNECTOR (LCD1) 3.35 DDR2 SO-DIMM (DDR1) 3.36 CF SOCKET (CN3) 50 1

24 4. WATCHDOG TIMER CONFIGURATION 4.1 WATCHDOG TIMER SETTING The WDT (Watch Dog Timer) is used to generate a variety of output signals after a use

25 // Set Watchdog outportb(IO_Port_Address,0x07); // Point to Logical Device Number Reg. outportb(IO_Port_Address+1,0x07); // Select logical

5. BIOS CONSOLE This chapter describes the AR-B5630 BIOS menu displays and explains how to perform common tasks needed to get up and running, and pres

27Time Setup The time format is： Hour：0 to 24 Minute：00 to 59 Second：00 to 59 To set the time, highlight the “Time” field and use the 【PageUp】/【Page

28Hyper-Threading Technology To enable HT Function Quick Power On Self Test When enabled, this field speeds up the Power On Self Test (POST) af

29ACPI Function Enable this function to support ACPI (Advance Configuration and Power Interface) ACPI Suspend Type This options for this field are S1

35.4 PNP/PCI SETUP ...

305.5 PERIPHERALS SETUP This option controls the configuration of the board’s chipset. Control keys for this screen are the same as for the previous

315.6 PC HEALTH SETUP This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds, volta

32First / Second / Third Boot Device These fields determine the device that the system searches first for an operating system. The option available

5.9 BIOS UPDATE The BIOS program instructions are contained within computer chips called FLASH ROMs that are located on your system board. The chips

4 0. PREFACE 0.1 COPYRIGHT NOTICE AND DISCLAIMER This document is copyrighted, 2008, by Acrosser Technology Co., Ltd. All rights are reserved. No pa

50.6 STATIC ELECTRICITY PRECAUTIONS Before removing the board from its anti-static bag, read this section about static electricity precautions. Stati

61. INTRODUCTION Welcome to the AR-B5630 ECIP AT/ATX Single Board Computer. The AR-B5630 is EPIC board with Socket P Intel Core™2 Duo or Core Duo or

7 1.2 SPECIFICATIONS Specifications (Proposed Specifications) Model Name  AR-B5630 V 1.0 Product Descriptions EPIC SBC support 65nm Intel uFC-P

8I/O 1 x RS-232 (COM1) DB9 Serial Port 2 x RS-232 (COM3/4) 1 x RS-232/422/485 (COM2) Pin Header Touch Screen N/A Parallel Port N/A GPIO 8 In

1.3 BLOCK DIAGRAM