Acrosser AR-ES6050FLD Manual de usuario

Revision: 1.0 1 Revision Description Date 1.0 Release 2010/08/20 AR-ES6050FLD System Guide

Revision: 1.0 10 3. Align the notch key on the Mini PCI-e card with rib on the slot. Figure 8 4. Push Mini PCI-e card horizontally . Figur

Revision: 1.0 11 5. Using two M2 screws to fasten Mini PCI-e card. Figure 10 6. Close the heat sink cover using the original screws to fa

Revision: 1.0 12 2.3 Installing the DDR2 SO-DIMM procedures 1. Unfasten the screw of the DDR cover and open the cover. Figure 11 2. Align

Revision: 1.0 13 3. Push DDR2 SO-DIMM horizontally and make sure it is locked by hooks of two sides of DDR2 socket. Figure 13 4. Recover th

Revision: 1.0 14 2.4 Assemble/Disassemble the DIN mounting bracket. 1. Hook the spring of the DIN mounting bracket onto the upper of DIN rail.

Revision: 1.0 15 3. Make sure they are locked together. Figure 16 4. Disassemble the DIN mounting bracket of AR-ES6050FLD system. Press dow

Revision: 1.0 16 3 Appendix Cable Pin Define 1. Com cable 2. Power Cable 110mm BLACK BLACK YELLOW YELLOW

Revision: 1.0 17 3. Switch Cable

Revision: 1.0 18 4 AR-B6050 Board Guide 4.1 Block Diagram

Revision: 1.0 19 AR-B6050 Board Specifications  Intel Atom N450 1.66GHz  Intel Graphics Media Accelerator 950  1 x SO-DIMM supports DDRII

Revision: 1.0 2 Contents 1 Introduction to AR-ES6050FLD...3 1.1 Specifications...

Revision: 1.0 20 4.2 AR-B6050 H/W Information This section describes the installation of AR-B6050. At first, it shows the Function diagram and the

Revision: 1.0 21 4.2.2 AR-B6050 LAYOUT (Bottom side) SODIMM1 CF

Revision: 1.0 22 4.3 Components and Jumps Setting List 1. JP1: LCD panel driving voltage selection. 2. ATX1: AT power input connector. 3. BAT1

Revision: 1.0 23 10. COM1: RS232 signal connector for port #1. 11. COM2: RS232 signal connector for port #2. 12. SATA1: SATA device connector

Revision: 1.0 24 19. VGA1: D-SUB-15 female connector for VGA output. 20. J1: CMOS data clear 21. USB3: Internal USB2.0 connector D-SUB-15 fema

Revision: 1.0 25 27. DIMM1: DDR-II SODIMM Socket. 28. CF1: Type-II compact flash card socket. DDR-II SODIMM Socket

Revision: 1.0 26 4.4 BIOS Setting The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS. To activate the BIO

Revision: 1.0 27 4.4.1 Main Setup Once you enter the InsydeH2O BIOS™ Setup Utility, the Main Menu will appear on the screen. Use the arrow keys to

Revision: 1.0 28 Cache RAM N/A This field displays the cache ram of the CPU. Total Memory N/A Displays the total memory available. SODIMM 0 N/A

Revision: 1.0 29 4.4.2 Advanced Chipset Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fie

Revision: 1.0 3 1 Introduction to AR-ES6050FLD AR-ES6050FLD is a fan-less embedded system that could be used by DIN mount for factory uses, VESA m

Revision: 1.0 30 4.4.3 Security Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you

Revision: 1.0 31 Setting a Password Follow these steps as you set the user or the supervisor password: 1. Use the ↑ and ↓ keys to highlight the S

Revision: 1.0 32 4.4.4 Power Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you ca

Revision: 1.0 33 4.4.5 Boot Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you can

Revision: 1.0 34 4.4.6 Exit Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you can

Revision: 1.0 35 4.5 WATCHDOG, GPIO, AND BYPASS PROGRAMMING 4.5.1 Watchdog Programming This section describes the usage of WATCHDOG. AR-B6050 int

Revision: 1.0 36 The WATCHDOG sample code of C language as below: //=========================================================================== //

Revision: 1.0 37 outportb(IO_Port_Address,0x2D); // Point to Global Reg. // Select Multi-Function pin, (Bit0=0 Watchdog Function) outpo

Revision: 1.0 38 printf("( For 10 seconds to reset. )\n"); } //====================================================================

Revision: 1.0 39 4.5.2 GPIO Programming This section describes the usage of GPIOs. AR-B6050 integrated eight bits, 5V TTL level, bidirectional, an

Revision: 1.0 4 1.3 System Dissection (1) Dimensions (2) Front Panel (3)System Configuration USB 1~4 ANTENNA HOL

Revision: 1.0 40 void Show_Fail(); void Show_Pass(); //=========================================================================== // Main proced

Revision: 1.0 41 outportb(IO_PORT_BASE+1,(inportb(IO_PORT_BASE+1) | 0x01)); // Select GPIO Port device outportb(IO_PORT_BASE,0x07); outpor

Revision: 1.0 42 // Exit W83627EHF Config outportb(IO_PORT_BASE,0xAA); if(result) Show_Fail(); else Show_Pass(); return resu

Revision: 1.0 43 //=========================================================================== // Function : Show_Pass() // I

檔名: ES6050_M10_0820_10am.doc 目錄: Z:\共用區\RD 交流區\Manual 暫存區(勿刪) 範本: C:\Documents and Settings\Roger_Nan\Application Data\Microsoft\Templates\Normal.do

Revision: 1.0 5 (3) System Configuration 3 2 4 891011121375 6 1

Revision: 1.0 6 Item Description Quantity1 LEFT COVER 1 2 PCI-104 CARD 1 3 DIN MOUNTING BRACKET 1 4 PCI-104 TAIL CONNECTOR 1 5 BASE 1 6 A

Revision: 1.0 7 2 Procedures of Assembly/Disassembly 2.1 Installing the CF card 1. Unfasten two screws of CF bracket and then take out the CF c

Revision: 1.0 8 3. Push CF card to the bottom of bracket to stop the forwarding at the bend of bracket. Figure 4 4. Push them into the CF

Revision: 1.0 9 2.2 Installing the Mini PCI-e interface card 1. Unfasten the six screws to take out the heat sink cover. Figure 6 2. Mayb